Nano V2 Earpiece Instructions

Table of Contents

1 Nano V2 Earpiece Instructions

What is a Nano Earpiece?

A nano earpiece is a auricular very small wireless which is inserted into the ear, remaining completely hidden. This type of hidden headphones are usually used for cheating in exams, use in presentations, espionage… The Nano Earpiece is the most popular model and one of the best sellers, but its operation can be complex without a guide.

What is a Vip Pro Pinganillo?

A vip pro earpiece is a auricular small size wireless which is inserted into the ear, remaining hidden. This type of hidden headphones are usually used for cheating in exams, use in presentations, espionage...

How does the Nano and Vip Pro Pinganillo work?

The two types of earpieces work using technology electromagnetic induction. The inductor collar generates an inductive wave that will cause a vibration in the earpieces, resulting in the sound. Thanks to induction technology we can use hidden earpieces with a very small size and resistant to inhibitors.

El nano earpiece reacts to inductive waves vibrating and generating sound. He vip pro earpiece requires a battery which amplifies inductive waves, providing more volume than the nano earpiece, and can be used in noisy environments

Is the Pinganillo Nano and Vip Pro Safe?

Yes, the two earpieces they are completely safe. Both of them they work because they react to electromagnetic induction emitted by the induction collar making sound. The nano earpiece does not have any electrical circuitry and with the vibration caused it generates sound. He Vip Pro earpiece requires a battery to amplify the induction received by the collar.

You can find more information in the section on security and compliance of the product located at the end of the web.

Technical characteristics

The nano earpiece is the smallest headset on the market with a size similar to that of a lentil. Is left over totally hidden being invisible from the outside.

The Nano V2 induction collar integrates a rechargeable battery inside. This battery can be charged at 100% in approximately 1 hour.

The inducing collar emits inductive waves causing the nano earpiece to vibrate and generating sound. The nano earpiece no charging required.

The recordings They are stored on a microSD included in the induction collar 512MB with up to 8 hours of recording. Supports microSD up to 16GB.

The autonomy of the collar is approximately 3 hours depending on volume. The induction collar must be turned off when not in use and while charging.

Kit Contents

1 – Puller Magnet

2 – Extractor Bar

3 – Nano earpieces (2 magnetic units)

4 – Nano V2 Inductor Collar with Push Buttons

5 – MicroSD 512MB (inserted into choke collar)

6 – USB-Type C adapter

7 – USB-MicroUSB adapter

+ Vip Pro SuperMini/UltraMini earpiece

8 – Vip Pro SuperMini or UltraMini earpiece

9 – 2 Batteries 337/SR416SW

Instructions

Step 0 - Original Product PingaOculto

Check that it is a original product of PingaOculto checking that the brand that appears on the product is the same.

If you have doubts about whether it is original, you can contact us and we will verify it. Contact us through: WhatsApp +34 644 098 320 o Email.

Step 1 - Store Recordings on microSD

Factory songs are included in the MP3 for testing, they can be deleted after testing.

The recordings are stored on a microSD of 512 Mb that is inserted into the side of the induction collar and offers storage of approximately 8 hours of recordings. The inductor collar accepts a card microSD up to 16 GB. To change it, push the integrated 512 Mb microSD inward and repeat the process to insert the new microSD until you hear a click.

To save recordings on the microSD you can:

Insert the microSD into the induction collar, turn on the collar with the side ON/OFF switch and connect the USB to the computer.
Use the included USB-microSD adapter to connect to your computer (faster transfer).
Use the USB-USB-Type C adapter (faster transfer).

It is important that they be stored in .mp3 format (if they are not there, you can convert them with the web: https://convertio.co/es/audio-converter/), to be stored in the root (not folders) and order them with numbers. In addition, you can also reduce the size of recordings compressing them using the web: https://www.mp3smaller.com/ and increase the volume of the recordings in: https://www.mp3louder.com

If the recordings are not ordered correctly when playing or listening to the songs that have already been deleted, the microSD must be formatted. Connect it to the computer and format it in FAT32 format.

Step 2 - Power and Status Lights

The choke collar is shipped with little or no charge, It is recommended to charge it before its first use. (See Step 7)

Turn on the Nano V2 inductor collar putting the switch in the ON position. will light the Green LED after a few seconds if the neckloop is charged. Wait for the collar to read the microSD on power up. The led at ignition indicates:

green light flashing: Loading new recording into memory and starting playback.
Steady green light: The microSD cannot be read, it is not inserted in the collar.

When recordings are playing, the LED indicates:

Steady green light: Paused recording.
green light flashing: Playing, recording change or button pressed.

when it is charging, the LED indicates:

steady red light: Charging.
no light: Inductor Collar 100% charged.

Step 3 - Earpiece Type

This model can be purchased only with the Nano Earpiece or also with a Vip Pro type Earpiece. The Nano Penguin offers little volume and can only be used in noise-free environments like exams or libraries. The Spy Earpiece Vip Pro offers more volume and can be used in environments with or without noise.

Select the earpiece model to see the configuration steps

Step 4 - Using the Kit with Vip Pro Earpiece

Step 4.1 - Stack Introduction

Select the earpiece model between the Vip Pro SuperMini (flesh color) or the Vip Pro UltraMini (black color)

Vip Pro UltraMini

Select the type of Vip Pro UltraMini earpiece. Both have the same operation only by varying the extraction method. In type A with extractor bar and type B pulling the transparent thread.

Type A

ATTENTION - To remove the Vip Pro UltraMini TYPE A earpiece from your ear, the battery must be inserted into the earpiece.

You should NEVER insert the Vip Pro UltraMini earpiece into your ear without first inserting the battery. on the Earpiece or the extractor bar will not work.

Unscrew the black cap from the earpiece and insert the stack with the positive pole facing upwards. Then screw the cap back on checking let it remain correctly screwed.

The battery begins to be consumed from the moment it is inserted on the earpiece and should withdraw if not to be used to prevent downloading. The stack model required for this version is 379-SR521SW.

type B

Unscrew the black cap from the earpiece and insert the stack with the positive pole facing upwards. Then screw the cap back on checking let it remain correctly screwed.

VIP Pro SuperMini

Unscrew the black cover of the spy headset and insert the battery with the positive pole up (where are the letters of the brand and the model of the battery is the positive pole).

Next, screw the cap back on, making sure it is screwed on tightly.

La battery begins to discharge as soon as it is inserted on the spy headset and must be removed if not in use to prevent discharge.

The battery model required for the vip pro spy headset is 337-SR416SW.

Step 4.2 - Cleaning Check Operation

This sound similar to an untuned radio is normal in all Vip Pro Earpieces. It is due to the constant amplification of the inductive waves emitted by the inductive element. This sound decreases when something is played and when the battery power decreases. Thanks to this technology, we have great autonomy and very small headphones.

Firstly, clean the ear well with a Q-tip, ear cleaning spray or water and dry well. Next, clean the earphone holes with a fine needle and be very careful to remove the wax that obstructs and can make you not hear anything.

Hold the spy headset close to your ear and check that you hear a sound similar to that of an untuned radio.

This sound indicates that it is turned on and works properly.

If the sound is very loud and can be heard without the earpiece in your ear, unscrew the cap and check that the battery is oriented with the positive pole + facing up and screw the cap back on carefully. If the lid or the battery are not aligned it will make this noise.

If you cannot hear the sound similar to an untuned radio, check that the battery is correctly inserted with the positive + side facing up and screw the cap back on carefully. If you have left the battery inserted for a long time, it will be dead and you will have to use the other battery included in the kit or a new one to get it working again.

Step 4.3 - Introduction and Placement of the Kit

Insert the earpiece into the left ear. You can also insert it on the right, but generally we hear better on the left. You can push the earpiece with your finger. It is not recommended to insert it too much, as it is not necessary to hide it.

Place the Kit as it appears in the image, remembering that the induction collar should always be on the neck under clothing so that the earpiece receives the sound.

play a recording pressing the button and verify that the green led flashes. Press the volume button without holding it down to increase the volume of the induction collar. The volume has 30 levels. When you hear a whistle means that the costumes is to the maximum* on the necklace. If you hold this button down it will not go up the volume.

*The volume to the maximum in the inducer collar drastically reduces the autonomy. You should set the volume to the minimum audible (typically 50-70%) on the collar (you can decrease the volume by pressing the volume – button and increase it by pressing the + button).

If you cannot hear the recording through the earpiece, but you do hear the sound of the radio without tuning, check that the induction collar is on the neck and that the volume is not at minimum on the induction collar. If you need more help contact us: WhatsApp +34 644 098 320.

If you cannot hear the sound similar to an untuned radio, check that the battery is inserted correctly with the positive + side facing up and screw the cap back on carefully. If you have left the battery inserted for a long time, it will be dead and you will have to use the other battery included in the kit or a new one to get it working again.

You are now done configuring the earpiece VIP Pro. You can follow with instructions in:

Step 5 - Using the Nano Earpiece Kit

If the vip pro earpiece works, the nano earpiece will work for sure. This is because the nano earpiece works because of the material it is made of.

It is recommended to first test the vip pro earpiece if you have purchased a kit with a vip pro earpiece.

Step 5.1 - Kit Parts

Extractor Bar, Extractor Magnet and Earpieces

The penguins (in the image indicated by the number 3) are the two smallest pieces and should part with the nail. You can find them in the Kit in a bag. Also included are extractor bar (2 in the picture) and the puller magnet (1 in the image).

Step 5.2 - Introducing Nano Earpiece

This step It is the most complex and may require several attempts to achieve the correct entry.. Si DO NOT enter it correctly you will hear low or not at all

Recommended For a correct introduction of the earpiece, keep the ear as clean as possible. We recommend using before introducing it swabs and/or spray for ear cleaning

Enter first a penguin (only one of the two that appear in the image indicated by a 3) in the left ear (we hear better through the left ear than through the right) through the following procedure:

Turn your head 90º so that the left ear where we are going to insert the earpiece is facing upwards.
Then drop the earpiece into your ear (You should never try to insert the earpiece with a cotton swab or similar, as it will not be inserted correctly).
keeping the same position with your head turned, shake your head and make circular movements until you notice the sensation of a drop of water falling into the ear and/or the clogged ear.

You may need to repeat this step several times

To check that the earpiece has been correctly inserted, put your hand to your ear (so that the earpiece does not fall to the ground) and turn your head to the opposite side. If the earpiece comes out of your ear easily when turning the head is that it has NOT been entered correctly. You must repeat the introduction steps.

also can check if it is correctly inserted by verifying that another person does not see the earpiece in the ear. If you can see it, DO NOT it is well introduced.

Tip: There are times when The earpiece just needs a little push to be correctly entered. If so, place the extractor magnet behind your ear, close to the neck. You will notice how the earpiece moves and you can finish placing it.

Tip 2: There are certain people who accumulate more amount of earwax, especially in the inner part of the ear, causing more difficult to introduce the earpiece. Remember clean the ear and Cleaning Sprays and sticks for the ears. Usually you will only need practice more to enter it correctly. If you can't enter it it is recommended that you have a ear cleaning to remove wax plugs.

If you can't enter it, contact us to help you: WhatsApp +34 644 098 320 o Email.

Step 5.3 - Kit Placement and Volume Adjustment

When the earpiece has been correctly inserted in the left ear, place the Kit as it appears in the image, remembering that the induction collar should always be on the neck under clothing so that the earpiece receives the sound.

play a recording pressing the button and verify that the green led flashes. Press the volume button to increase the volume of the inducer collar. The volume has 30 levels, between the minimum and the maximum. When you hear a whistle means that the costumes is to the maximum* on the necklace. Holding down this button will not increase the volume. Must press the button without holding it down.

Check if the volume it provides is enough a penguin (sufficient in most cases) if we have inserted the earpiece correctly, if the volume has been increased, the collar has enough charge and is located on the neck).

If you hear very low, Also insert the other earpiece into your right ear or try turning up the volume on the Nano V2 Neckloop (30 levels between minimum and maximum volume).

(A single earpiece in the left ear is recommended, since when trying to insert one in each ear, the first one will be misplaced when introducing the second one). (It is VERY likely that if we do not hear well with an earpiece in the left ear it is because we have not inserted the earpiece correctly, the volume is not the maximum in the collar, the neckloop does not have enough charge or it is not in the neck).

Step 6 - Multifunction and Volume Buttons

The next/previous buttons on inducer collar are locked because they are replaced by the buttons that are located on the feet.

The push buttons located on the feet have various functions:

1 Click Push Button: Next/Previous Recording.
Hold Button: Fast Forward/Backward.

The Nano V2's volume buttons have several functions:

Hold Button ➕ : Switch between play mode (In order-Random-Repeat)
1 Click Button ➕ : Raise the volume. When the volume is maximum, a beep is emitted by the earpiece. The induction collar has 30 volume levels. ⚠ If you hold down this button it will not go up the volume. Must press the button without holding it down.
1 Click Button ➖ : Decrease the volume. When the volume is minimal you will not hear anything through the earpiece. The induction collar has 30 volume levels. ⚠ If you keep this button pressed, it will not download the volume. Must press the button without holding it down.
Hold Button ➖ : Start recording from the beginning.

*Maximum volume on the induction collar drastically reduces autonomy. You must adjust the volume to the minimum audible (normally 50-70%) on the inductor collar (you can adjust the volume with the + and – button on the inductor collar).

Step 7 - Battery, Earpiece and Battery Removal

Remember to turn off the neckloop while not in use and while it is charging.

Battery charge

La autonomy of the Nano V2 device is approximately 3 hours.

To charge it, connect el USB to a computer or charger up to 5V and 1A. The estimated time of charge is 1-1,5 hours. The device is fully charged when the red light disappears while its charging. The Nano V2 must be turned off while charging.

The battery should be charged/discharged at least once every 1 months to increase battery life.

Earpiece Removal

Step 7.1 - Removing the Nano Earpiece

remove the earpiece approaching the extractor bar (indicated in the image with a 2) with puller magnet (indicated with a 1) at its base to the ear as you can see in the first image.

Another VERY effective extraction method es hold with one finger the puller magnet inside the ear and shake your head while keeping it rotated as in the second image. It can be hard to remove the first few times, but after several attempts it will succeed.

Also the earpiece may have already been removed and fallen to the ground, check if it is still in your ear by connecting the Kit and checking if you hear when playing a recording at maximum volume.

If you cannot extract it, contact us to help you: WhatsApp +34 644 098 320 o Email.

It is recommended to clean the earpiece with water or alcohol, the extractor magnet and the extractor bar before and after each use.

Lastly, remember to turn off the collar inductor to prevent it from discharging.

Step 7.2 - Removing the Vip Pro Earpiece

Select the earpiece model between the Vip Pro SuperMini (flesh color) or the Vip Pro UltraMini (black color)

Vip Pro UltraMini

Select the type of Vip Pro UltraMini earpiece. Both have the same operation only by varying the extraction method. In type A with extractor bar and type B pulling the transparent thread.

Type A

ATTENTION - To remove the Vip Pro UltraMini TYPE A earpiece from your ear, the battery must be inserted into the earpiece.

You should NEVER insert the Vip Pro UltraMini earpiece into your ear without first inserting the battery. on the Earpiece or the extractor bar will not work.

Remove the earpiece by inserting the removal bar into your ear. Remember that this is magnetized to the battery, so You should never insert the earpiece into your ear without first inserting the battery.

Lastly, remember to disconnect the battery when you finish using the earpiece so it doesn't download.

⚠ If you can't extract it, contact us to help you: WhatsApp +34 644 098 320 o Email.

type B

Remove the earphone by pulling the transparent thread with your fingers. If you don't get it, you can try to pull the transparent thread with tweezers.

Lastly, remember to disconnect the battery when you finish using the spy headset to prevent further consumption.

VIP Pro SuperMini

Remove the earphone by pulling the transparent thread with your fingers. If you don't get it, you can try to pull the transparent thread with tweezers.

Lastly, remember to disconnect the battery when you finish using the spy headset to prevent further consumption.

Can check the VideoTutorial along with instructions to better understand how the earpiece works:

If you have questions, don't hesitate to contact us! 😉

Frequent Problems

the penguins can be complex products in its operation. Check below the frequent problems nano penguin v2 and its solution.

1 - Doesn't work

Nano earpieces work because of the material they are made of, a piezoelectric material, and not due to any internal electronics in the earpieces. For this reason it is impossible for nano earpieces not to work and the The problem will be the inducer collar or the files. Follow the steps and tests indicated in the next section (2 – I can't hear anything or very low).

Si the vip pro earpiece does not work follow the checks below:

Clean the earphone holes with a fine needle and be very careful to remove earwax that obstructs the earpiece and can make you not hear anything.
Check that the battery is charged. If it has been left on the spy headset for a long time, it will download and you must use a new battery. The battery discharges even when not in use.
Unscrew the black cap of the spy headset and insert the battery with the positive pole facing up (where the letters of the brand and the battery model are the positive pole).
Screw the cap back on, making sure it is screwed tightly.

If you hear the sound similar to an untuned radio by putting the earpiece in your ear with the battery inserted, the earpiece is working and the problem will be another. Follow the steps indicated in the next section (2 – I can't hear anything or very low).

The battery begins to be consumed from the moment it is inserted in the earpiece and must be removed if it is not going to be used to avoid its discharge.

2 - I can't hear anything or very low

This is one of the most common problems in the penguins exist several possible reasons for which you hear nothing or very little. We are going to carry out a series of tests:

Check on the microSD integrated in the inductor collar:

The files are in MP3 format. If they are not there, you can convert them with the web: https://convertio.co/es/audio-converter/.
The recordings are not in folders, they must be in the root of the microSD.
The microSD is maximum 16GB.
The microSD is correctly inserted in the collar inductor.

Es It is advisable to try again with a single file in MP3 format of a song like this: https://www.pingaoculto.es/wp-content/uploads/2024/04/Interupt、Luna-LePage-Power-In-Your-Soul.mp3. If it works with this file, it is a problem with the files.

With which of the two earpieces are you experiencing the problem?

Spy Earpiece Nano

If the vip pro earpiece works, the nano earpiece will work for sure. This is because the nano earpiece works because of the material it is made of.

It is recommended to first test the vip pro earpiece if you have purchased a kit with a vip pro earpiece.

Extractor Bar, Extractor Magnet and Earpieces

green light flashing: Loading new recording into memory and starting playback.
Steady green light: The microSD cannot be read, it is not inserted in the collar.

When recordings are playing, the LED indicates:

Steady green light: Paused recording.
green light flashing: Playing, recording change or button pressed.

when it is charging, the LED indicates:

steady red light: Charging.
no light: Inductor Collar 100% charged.

Place together the Extractor Magnet and the two earpieces and place them in contact with the inductor collar, which must be rolled as in the picture. The extractor magnet, being also made of a piezoelectric material, reacts to inductive waves in the same way as the earpieces, vibrating and causing the sound, for this reason we will use it together with the earpieces to carry out the test.

play a recording pressing the button and verify that the green led blinks. While playing, bring your ear close to the extractor magnet and the earpieces that are in contact with the induction collar and check if it is heard or vibrates. If it is not heard or vibrates, press the button costumes to increase the volume of the inducer collar. The volume has 30 levels, between the minimum and the maximum. If you hold this button down it will not go up the volume. Must press the button without holding it down.

Si vibrate and/or can be heard the kit It's working correctly.

If they do not vibrate or hear anything, check the format of the recordings (must be .mp3) and verify that the induction collar is charged, that the cable is coiled as in the image, that you have positioned the extractor magnet and the two earpieces stuck to the cable and that the volume is maximum while playing the recording. If you need more help contact us: WhatsApp +34 644 098 320 o Email.

If in the previous step when carrying out the test you have noticed how the extractor magnet together with the earpieces vibrate or sound, the kit is working correctly and the problem is:

El inductor collar has no charge or has low charge.
El induction collar was not on the neck while being tested with the earpiece in the ear.
El recording file volume is too low. They can be increased in volume with the web https://www.mp3louder.com.
El inducer collar volume is low. It can be raised by pressing the + button (without holding it down). There are 30 volume levels and it should not be set too loud to increase its autonomy.
The earpiece has not been correctly inserted. (The MOST likely option). Follow the earpiece input steps again:

Turn your head 90º so that the left ear where we are going to insert the earpiece is facing upwards.
Then drop the earpiece into your ear (You should never try to insert the earpiece with a cotton swab or similar, as it will not be inserted correctly).
keeping the same position with your head turned, shake your head and make circular movements until you notice the sensation of a drop of water falling into the ear and/or the clogged ear.

You may need to repeat this step several times

also can check if it is correctly inserted by verifying that another person does not see the earpiece in the ear. If you can see it, DO NOT it is well introduced.

If you can't enter it, contact us to help you: WhatsApp +34 644 098 320 o Email.

If you hear very low, Also insert the other earpiece into your right ear or try turning up the volume on the Nano V2 Neckloop (30 levels between minimum and maximum volume).

Spy Earpiece Vip Pro

Clean the earphone holes with a fine needle and be very careful to remove earwax that obstructs the earpiece and can make you not hear anything.
Check that the battery is charged. If it has been left on the spy headset for a long time, it will download and you must use a new battery. The battery discharges even when not in use.
Unscrew the black cap of the spy headset and insert the battery with the positive pole facing up (where the letters of the brand and the battery model are the positive pole).
Screw the cap back on, making sure it is screwed tightly.
If you hear a sound similar to that of an untuned radio When you put the spy earpiece in your ear with the battery inserted, the spy headset is working and the problem is another.

Place the induction collar on the neck and the earpiece in the ear and check that the microSD is inserted into the side of the collar with the recordings.

⚠ The battery begins to be consumed from the moment it is inserted in the earpiece and must be removed if it is not going to be used.

The volume to the maximum in the inducer collar drastically reduces the autonomy. You should set the volume to the minimum audible (typically 50-70%) on the collar (you can decrease the volume by pressing the volume – button and increase it by pressing the + button).

3 - I only hear out of one ear / earpiece

If the vip pro earpiece works, the nano earpiece will work for sure. This is because the nano earpiece works because of the material it is made of.

It is recommended to first test the vip pro earpiece if you have purchased a kit with a vip pro earpiece.

In nano earpieces this failure is impossible. If one device works, the other works too. This is because the earpieces work because of the material they are made of, a piezoelectric material, and not due to any internal electronics in the earpieces. The material reacts to the inductive waves of the induction collar by vibrating and making sound.

Most likely, the earpiece has not been correctly inserted into the ear, we are confusing the extractor magnet with the earpieces or two earpieces together or that let's hear more through one ear (We normally hear more through the left ear).

If the volume obtained by the earpiece in one ear is sufficient, it is recommended to use it with a single earpiece and save the other.

4 - A very loud sound sounds, like a bee

Untuned radio-like sound is normal in all Vip Pro spy headphones. It is due to the constant amplification of the inductive waves emitted by the collar.
If the sound is very loud, and You can hear it even when it's not in your ear, follow the steps below:

If the sound is very loud and can be heard even with the earphone out of the ear, unscrew the cap and Check that the battery is oriented with the positive + pole facing up and that the cap is screwed on correctly and aligned. If the problem persists, remove the cover again and Gently pull the spring inside the earphone with your fingernail or tweezers. Thus, will be deformed and contact will be made correctly. Can be necesario perform this adjustment occasionally or on first use.

5 - Recordings are out of order

If the recordings are out of order and that's it has numbered them from the way: 1.mp3,2.mp3,3.mp3… or if you listen to recordings already deleted in the microSD you must format it in format FAT32.

Save the recordings to your computer or mobile first and then proceed to format the microSD. You can check on Google how to format a microSD on Mac/Windows or other devices.

Also the playback mode may have been changed. To change it, you must hold down the + button on the induction collar and it will change between in random-order-repeat.

6 - Steady green light and does not work

If the green light is steady must be verified:

microSD inserted into the side of the induction collar.
microSD up to 16GB
We have pressed the button. Play/Pause and the green light status does not change.
We have not entered the files in MP3 format or the files are corrupt.
We have introduced large recordings, we must reduce their size with the web https://www.mp3smaller.com/es/.

7 - The button does not work or does not work as it should

The next/previous buttons on inducer collar are locked because they are replaced by the buttons that are located on the feet.

It is important verify that we have not changed the playback order by holding down the + button on the induction collar. To change it, you must hold down the + button on the induction collar and it will change between in random-order-repeat.

The push buttons located on the feet have various functions:

1 Click Push Button: Next/Previous Recording.
Hold Button: Fast Forward/Backward.

The Nano V2's volume buttons have several functions:

Hold Button ➕ : Switch between play mode (In order-Random-Repeat)
1 Click Button ➕ : Raise the volume. When the volume is maximum, a beep is emitted by the earpiece. The induction collar has 30 volume levels. ⚠ If you hold down this button it will not go up the volume. Must press the button without holding it down.
1 Click Button ➖ : Decrease the volume. When the volume is minimal you will not hear anything through the earpiece. The induction collar has 30 volume levels. ⚠ If you keep this button pressed, it will not download the volume. Must press the button without holding it down.
Hold Button ➖ : Start recording from the beginning.

8 - I can't extract the earpiece

With which of the two earpieces are you experiencing the problem?

Spy Earpiece Nano

You may have to try several times until it is successfully removed.

remove the earpiece approaching the extractor bar (indicated in the image with a 2) with puller magnet (indicated with a 1) at its base to the ear as you can see in the first image.

If you cannot extract it, contact us to help you: WhatsApp +34 644 098 320 o Email.

It is recommended to clean the earpiece with water or alcohol, the extractor magnet and the extractor bar before and after each use.

Lastly, remember to turn off the collar inductor to prevent it from discharging.

Spy Earpiece Vip Pro

Remove the earphone by pulling the transparent thread with your fingers. If you don't get it, you can try to pull the transparent thread with tweezers.

Lastly, remember to disconnect the battery when you finish using the spy headset to prevent further consumption.

9 - The Choke Collar has stopped working

Most likely, has stayed on and the battery has been depleted. Perform a full charge. It is also possible that the volume has gone down, you must raise it by repeatedly pressing the + button on the Nano V2 while it is on and playing.

If you have already checked that you have charge and that the volume of the Nano V2 is maximum, follow the steps indicated in the section 2 -I can't hear anything or very low of frequent problems.

If the Kit does not work, please contact us to help you: WhatsApp +34 644 098 320 o Email.

10 - Low Autonomy

🔋❗ The volume to the maximum in the induction collar drastically reduces autonomy. You must adjust the volume to audible minimum (typically 50-70%) at neckloop (you can decrease the volume by repeatedly pressing the volume – button and increase it by repeatedly pressing the + button).

Can check the VideoTutorial along with instructions to better understand how the earpiece works:

If you have questions, don't hesitate to contact us! 😉

Security and Compliance

Below is indicated important product information in relation to the security and compliance that guarantee proper and safe use of the product:

⚠ FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER DAMAGE OR INJURY.

⚠ WARNING: Do not use or store the product near other electronic equipment because the magnetic field of adjacent electrical equipment will seriously damage or interfere with the product. Also do not use this product if you have impaired hearing which may be affected, if you use hearing aids, or if you are using a pacemaker or any electronic medical device.

Product specifications:

Model Name: Nano V2 / Nano V2 + Vip Pro SuperMini / Nano V2 + Vip Pro UltraMini

Model number: N-03/N-04/N-05

Product identifier: B09W1RBS68 / B09Y3LYZTW/ B09W1R5873

Product battery: Integrated Lithium-Ion type with 500 mAh capacity

Electrical Rating: Power: 100-240V 50/60Hz 0.15A

Batteries Included: 2 x Silver Oxide Batteries type 337-SR416SW

Operating temperature: 0 to 35ºC

Product Use: Do not expose your device or adapter to liquids. If your device or adapter gets wet, carefully unplug all cables without getting your hands wet, and wait for the device and adapter to dry completely before plugging them back in. Do not try to dry your device or adapter with an external heat source, such as a microwave oven or blow dryer. If the device or adapter is damaged, stop using it immediately. Use only the supplied accessories to power your device. To avoid the risk of electric shock, do not touch the device or the cables connected to it during a thunderstorm. The cables and/or adapters are only designed for indoor use.

Legal Notice: PingOc Now SL is not responsible for the fraudulent or erroneous use of the product due to the lack of understanding or reading of the information in the instructions and precautions. This product is not a toy and must not be used contrary to current applicable laws. If you have any questions you can contact us before using the product.

For EU customers: Hereby, PingaOculto, declares that the type of radio equipment is in accordance with Directive 2014/53/EU.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

FCC Compliance: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet the general RF exposure requirement. The device can be used in portable exposure conditions without restrictions.

Radio Frequency Exposure Compliance: As a health protection measure, this device complies with the limits for exposure of the general public to electromagnetic fields in accordance with council recommendation 1999/519/EC. This device can be placed on the body avoiding prolonged use of it for more than 5 hours.

How to recycle your device properly: Disposal of certain electronic devices is regulated in some areas. Make sure you comply with local regulations and laws.

Additional Safety and Compliance Information: For additional information on safety, recycling and compliance or other important issues related to your device, do not hesitate to contact us through any of the available means of contact. Means of contact with: Email contact@pingaoculto.com, Call/WhatsApp +34 644 098 320.

Limited Warranty: All official brand items PingaOculto have 2 year minimum warranty. This guarantee may be extended or reduced depending on the country where the sale takes place, as is the case by law in Spain where it is extended to 3 years as established by Decree-Law 7/2021 with respect to the Guarantee on the Sale of Goods. of consumption. We reserve the right to deny the guarantee of a product if improper or negligent use by the client is verified, similar to those reflected in: https://www.pingaoculto.es/garantias-y-devoluciones/ If you need to contact us due to a failure, you can do so by email: contact@pingaoculto.com or by Call/WhatsApp: +34 644 098 320.

More Information

Do you want to contact us?

follow us on

Nano V2 Earpiece Instructions

What is a Nano Earpiece?

What is a Vip Pro Pinganillo?

How does the Nano and Vip Pro Pinganillo work?

Is the Pinganillo Nano and Vip Pro Safe?

Technical characteristics

Kit Contents

Instructions

Step 0 - Original Product PingaOculto

Step 1 - Store Recordings on microSD

Step 2 - Power and Status Lights

Step 3 - Earpiece Type

Step 4 - Using the Kit with Vip Pro Earpiece

Step 4.1 - Stack Introduction

Step 4.2 - Cleaning Check Operation

Step 4.3 - Introduction and Placement of the Kit

Step 5 - Using the Nano Earpiece Kit

Step 5.1 - Kit Parts

Extractor Bar, Extractor Magnet and Earpieces

Step 5.2 - Introducing Nano Earpiece

Step 5.3 - Kit Placement and Volume Adjustment

Step 6 - Multifunction and Volume Buttons

Step 7 - Battery, Earpiece and Battery Removal

Step 7.1 - Removing the Nano Earpiece

Step 7.2 - Removing the Vip Pro Earpiece

Frequent Problems

1 - Doesn't work

2 - I can't hear anything or very low

3 - I only hear out of one ear / earpiece

4 - A very loud sound sounds, like a bee

5 - Recordings are out of order

6 - Steady green light and does not work

7 - The button does not work or does not work as it should

8 - I can't extract the earpiece

9 - The Choke Collar has stopped working

10 - Low Autonomy

Security and Compliance