+34 644 098 320
+34 91 417 04 02
WhatsApp +34 644 098 320
Call + 34 972 25 62 12
⌛ Urgent Delivery 24-48 Hours Available 📦
Table of Contents
1 – Puller Magnet
2 – Nano Earpiece Extractor Bar
3 – Nano earpieces (2 magnetic units)
4 – Nano V3 Inductor Collar
5 – USB charging cable
6 – Vip Pro SuperMini earpiece
7 – 2 Batteries 337/SR416SW
Check that it is a original product of PingaOculto checking that the brand that appears on the cards included with the product is the same as the one in the image.
If you have doubts about whether the product is original, you can contact us by attaching an image and we will verify it. Contact us via: WhatsApp +34 644 098 320 o Email.
Turn on the Nano V3 putting the switch located on the side in the ON position. will light the blue led if the neckloop is charged.
Put the whole Kit on a table or flat surface and connect the mobile through the headphone jack. Remove the cover of your mobile, since it can prevent the correct connection. If your mobile needs an adapter, verify that it works with other headphones to rule out a problem with the same one and check that it is original.
On some iPhone models and a compatibility failure has been detected in the use of the device with non-original adapters when making a phone call. You need to use an original adapter or use another mobile.
Two types of earpiece are included in this model, being able to choose the one you prefer according to the situation. The Nano Penguin offers little volume and can only be used in noise-free environments like exams or libraries. The Vip Pro SuperMini Earpiece offers more volume and can be used in environments with or without noise.
Select the earpiece model you prefer to see the configuration steps
Unscrew the black cap from the earpiece and insert the stack with the positive pole facing upwards. Then screw the cap back on checking let it remain correctly screwed.
The battery begins to be consumed from the moment it is inserted on the earpiece and should withdraw if not to be used to avoid downloading. The model of the battery that the earpiece requires is 337-SR416SW.
Bring the earpiece to your ear and check that you can hear a sound similar to an untuned radio. This sound indicates that you are powered on and working properly.
⚠ If the sound is very loud, it can be heard without the earpiece in your ear, unscrew the cap and check that the battery is oriented with the positive pole + facing up and screw the cap back on carefully. If the lid or the battery are not aligned it will make this noise.
⚠ If you cannot hear the sound similar to an untuned radio, check that the battery is correctly inserted with the positive pole + facing up and screw the cover back on carefully. If you have left the battery inserted for a long time, it will be dead and you will have to use the other battery included in the kit or a new one to get it working again.
Place the Kit as it appears in the image remembering that the induction collar should always be on the neck under clothes. Put the earpiece in the ear always with the battery inside.
Play a song on your mobile and while playing turn up the volume to the maximum from your mobile. Check if it is heard on the earpiece.
For more security it is recommended to fix the induction collar with cloth or plastic tape to your skin so that it does not move during use. For repeated use you can even sew it to sweatshirts or jackets. Remember that the Induction Collar is not washable.
⚠ If the song is not heard through the earpiece, but you do hear the sound of the radio without tuning, check that the inductor collar is on the neck and that the mobile is correctly connected and with the volume at maximum. If it doesn't work try another mobile. If you need more help contact us: WhatsApp +34 644 098 320 o Email.
You are now done configuring the earpiece vip pro supermini. You can follow with instructions in:
The penguins (in the image indicated by the number 3) are the two smallest pieces and should part with the nail. You can find them in the Kit in a bag. Also included are extractor bar (2 in the picture) and the puller magnet (1 in the image).
Place together the Extractor Magnet and the two earpieces and place them in contact with the induction collar like in the image. The extractor magnet, being also made of a piezoelectric material, reacts to inductive waves in the same way as the earpieces, vibrating and causing the sound and for this reason we will use it together with the earpieces to carry out the test.
Play a song on your mobile/MP3 and while playing turn up the volume to the maximum from your mobile. Bring your ear closer to the extractor magnet and to the earpieces that are in contact with the induction collar and check if it is heard and/or vibrates.
Si vibrate and/or can be heard the kit It's working correctly.
If they do not vibrate or hear anything, repeat the steps with another mobile and verify that the induction collar has a charge, that the cable is coiled as in the image, that you have placed the extractor magnet and the two earpieces attached to the cable and that the volume is maximum while the song is playing. If you need more help contact us: WhatsApp +34 644 098 320 o Email.
Enter first a penguin (only one of the two that appear in the image indicated by a 3) in the left ear (we hear better through the left ear than through the right) through the following procedure:
It may be necessary to spread this step several times
For check that the earpiece has been correctly inserted, put your hand to your ear (so that the earpiece does not fall to the ground) and turn your head to the opposite side. If the earpiece comes out of your ear easily when turning the head is that it has NOT been entered correctly. You must repeat the introduction steps.
also can check if it is correctly inserted by verifying that another person does not see the earpiece in the ear. If you can see it, DO NOT it is well introduced.
Tip: There are times when The earpiece just needs a little push to be correctly entered. If so, place the extractor magnet behind your ear, close to the neck. You will notice how the earpiece moves and you can finish placing it.
Tip 2: There are certain people who accumulate more amount of earwax, especially in the inner part of the ear, causing more difficult to introduce the earpiece. Remember clean the ear with Cleaning Sprays and sticks for the ears. Usually you will only need practice more to enter it correctly. If you can't enter it it is recommended that you have a ear cleaning to remove wax plugs.
If you can't enter it, contact us to help you: WhatsApp +34 644 098 320 o Email.
When the earpiece has been correctly inserted in the left ear, place the Kit on the body as it appears in the image, remembering that the induction collar should always be on the neck under clothing so that the earpiece receives the sound.
Play the song, recording or phone call by turning the volume up to the maximum on your mobile to check if the volume it provides is enough a penguin (sufficient in most cases) if we have inserted the earpiece correctly, if the volume is maximum, the collar has enough charge and is located on the neck).
If you hear very low, Also insert the other earpiece into your right ear or try turning up the volume on the Nano V3 Neckloop (different volume than mobile).
For increase the volume of the neckloop (different volume than mobile) hold down the + button of the Nano V3 while the earpiece is on the left ear and the neckloop on the neck. When you hear a whistle means that the volume is at maximum* on the necklace.
(A single earpiece in the left ear is recommended, since when trying to insert one in each ear, the first one will be misplaced when introducing the second one). (It is VERY likely that if we do not hear well with an earpiece in the left ear it is because we have not inserted the earpiece correctly, the volume is not the maximum in the mobile, the induction collar does not have enough charge or it is not on the neck).
*The volume to the maximum in the inducer collar drastically reduces the autonomy. You must adjust the volume to the maximum on the mobile and to the minimum audible (usually 50-70%) on the neckloop (you can decrease the volume by holding down the volume – button and increase it by holding down the + button).
You can use this device by phone call or with recordings. He integrated microphone is located on the top of the Nano V3.
El button A performs the following functions:
The volume buttons of the Nano V3 have the functions:
This device has two volumes, the one for your mobile and the one for the Nano V3 To increase autonomy it is recommended DO NOT max out the volume on the Nano V3. The optimal volume is 50-70% in the Nano V3 inductor collar and 100% in the mobile.
La autonomy of the Nano V3 device is approximately 4 hours.
to load it connect it to the current with the cable of the Kit. The estimated time of charge is 1-1,5 hours. The device is fully charged when the red light disappears while its charging. Remember to check that the Nano V3 is turned off while charging.
remove the earpiece approaching the extractor bar (indicated in the image with a 2) with puller magnet (indicated with a 1) at its base to the ear as you can see in the first image.
Another VERY effective extraction method es hold with one finger the puller magnet inside the ear and shake your head while keeping it rotated as in the second image. It can be hard to remove the first few times, but after several attempts it will succeed.
As well the earpiece may have already been removed and fallen to the ground, check if it is still in your ear by connecting the Kit and checking if you hear when playing a song at maximum volume.
If you cannot extract it, contact us to help you: WhatsApp +34 644 098 320 o Email.
It is recommended to clean the earpiece with water or alcohol, the extractor magnet and the extractor bar before and after each use for better hygiene.
Finally, remember to turn off the collar inductor to prevent it from discharging.
Remove the earpiece by pulling the transparent thread with your fingers. If you don't make it, you can try pulling of the transparent thread with a tweezer.
Finally, remember to disconnect the battery when you finish using the device to prevent it from downloading.
⚠ If you can't extract it, contact us to help you: WhatsApp +34 644 098 320 o Email.
Can check the VideoTutorial along with instructions to better understand how the earpiece works:
If you have questions, don't hesitate to contact us! 😉
the penguins can be complex products when putting them into operation. Check below the frequent problems of nano v3 vip pro supermini earpiece.
Nano earpieces work because of the material they are made of, a piezoelectric material, and not due to any internal electronics in the earpieces. For this reason it is impossible for nano earpieces not to work and The problem will be the inductor collar or the mobile. Follow the steps and tests indicated in the next section (3 – I can't hear anything or very low).
Si vip pro supermini earpiece does not work follow the checks below:
The battery begins to be consumed from the moment it is inserted in the earpiece and must be removed if it is not going to be used to avoid its discharge. The battery model that the earpiece requires is 337-SR416SW.
With which of the two earpieces are you experiencing the problem?
Check that you have separated the earpieces (indicated in the image with the number 3), which are the two smallest pieces. You can find them in an accessory bag in the kit.
If in the previous step when carrying out the test you have noticed how the extractor magnet together with the earpieces vibrate or sound, the kit is working correctly and the problem is:
If you hear the sound similar to an untuned radio by putting the earpiece in your ear with the battery inserted, the earpiece is working
Place the induction collar on the neck and the earpiece in the ear and checking that it is connected to the mobile, play a song at maximum volume on your mobile. As well turn up the volume all the way on the neckloop holding down the + button of the necklace.
⚠ The battery begins to be consumed from the moment it is inserted in the earpiece and must be removed if it is not going to be used to avoid its discharge. The model of the stack is 337-SR416SW.
The volume to the maximum in the inducer collar drastically reduces the autonomy. You should set the volume to the minimum audible (typically 50-70%) on the collar (you can decrease the volume by pressing the volume – button and increase it by pressing the + button).
If one earpiece works, the other works too. This is because the earpieces work because of the material they are made of, a piezoelectric material, and not due to any internal electronics in the earpieces. The material reacts to the inductive waves of the induction collar by vibrating and making sound.
Most likely, the earpiece has not been correctly inserted into the earOr this let's hear more for one than for another (normally we hear more through the left ear than through the right).
If the volume obtained by the earpiece in one ear is sufficient, it is recommended to use it with a single earpiece and save the other spare.
⚠ The A button is not necessary if the functions are performed directly from the mobile and may not be compatible with some mobiles.
The built-in microphone works like a handsfree for phone calls, but you can not work on some mobiles. It is recommended Check your mobile settings when making the call or use another mobile.
You may have to try several times until it is successfully removed.
remove the earpiece approaching the extractor bar (indicated in the image with a 2) with puller magnet (indicated with a 1) at its base to the ear as you can see in the picture.
Most likely, has stayed on and the battery has been depleted. Perform a full charge. It is also possible that the volume has gone down, you must upload it by holding the + button of the Nano V3 while it is turned on and connected to your mobile.
If you have already verified that you have a charge and that the volume of your mobile and the Nano V3 is maximum follow the steps indicated in section 2 -I can't hear anything or very low of frequent problems.
If the Kit does not work, contact us to help you: WhatsApp +34 644 098 320 o Email.
🔋❗ The volume to the maximum in the induction collar drastically reduces autonomy. You must adjust the maximum volume on mobile and audible minimum (typically 50-70%) at neckloop (you can decrease the volume holding down the button – volume and increase it by holding down the + button).
Below is the important product information in relation to the security and compliance that guarantee proper and safe use of the product:
⚠ WARNING: Do not use or store the product near other electronic equipment because the magnetic field of adjacent electrical equipment will seriously damage or interfere with the product. Also do not use this product if you have impaired hearing which may be affected, if you use hearing aids, or if you are using a pacemaker or any electronic medical device.
® PingaOculto. All rights reserved.
Product specifications:
Model Name: Nano V3 + Vip Pro SuperMini
Model Number: N-07
Product identifier: B09Y3N4L9J
Product battery: Integrated Lithium-Ion type with 500 mAh capacity
Electrical Rating: Power: 100-240V 50/60Hz 0.15A
Batteries Included: 2 x Silver Oxide Batteries type 337-SR416SW
Operating temperature: 0 to 35ºC
Product Use: Do not expose your device or adapter to liquids. If your device or adapter gets wet, carefully unplug all cables without getting your hands wet, and wait for the device and adapter to dry completely before plugging them back in. Do not try to dry your device or adapter with an external heat source, such as a microwave oven or blow dryer. If the device or adapter is damaged, stop using it immediately. Use only the supplied accessories to power your device. To avoid the risk of electric shock, do not touch the device or the cables connected to it during a thunderstorm. The cables and/or adapters are only designed for indoor use.
Terms of use: PingOc Now SL is not responsible for the fraudulent or erroneous use of the product due to the lack of understanding or reading of the information in the instructions and precautions. This product is not a toy and must not be used contrary to current applicable laws. If you have any questions you can contact us before using the product.
For EU customers: Hereby, PingaOculto, declares that the type of radio equipment is in accordance with Directive 2014/53/EU.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC Compliance: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet the general RF exposure requirement. The device can be used in portable exposure conditions without restrictions.
Radio Frequency Exposure Compliance: As a health protection measure, this device complies with the limits for exposure of the general public to electromagnetic fields in accordance with council recommendation 1999/519/EC. This device can be placed on the body avoiding prolonged use of it for more than 5 hours.
How to recycle your device properly: Disposal of certain electronic devices is regulated in some areas. Make sure you comply with local regulations and laws.
Additional Safety and Compliance Information: For additional information on safety, recycling and compliance or other important issues related to your device, do not hesitate to contact us through any of the available means of contact. Means of contact with: Email contact@pingaoculto.com, Call/WhatsApp +34 644 098 320.
Limited Warranty: All official brand items PingaOculto have 2 year minimum warranty. This guarantee may be extended or reduced depending on the country where the sale takes place, as is the case by law in Spain where it is extended to 3 years as established by Decree-Law 7/2021 with respect to the Guarantee on the Sale of Goods. of consumption. We reserve the right to deny the guarantee of a product if improper or negligent use by the client is verified, similar to those reflected in: https://www.pingaoculto.es/garantias-y-devoluciones/ If you need to contact us due to a failure, you can do so by email: contact@pingaoculto.com or by Call/WhatsApp: +34 644 098 320.
Anywhere in the world
Up to 14 calendar days
Quick and Efficient Management
PayPal / MasterCard / Visa