+34 644 098 320
+34 91 417 04 02
WhatsApp +34 644 098 320
Call + 34 972 25 62 12
🇪🇸 - Select your language
- Select your language
- Wähle deine Sprache
???????? - Choose your language
🇵🇹 – Select your language
🇳🇱 – Selecteer je taal
- Välj ditt språk
- Wybierz swój język
Table of Contents
1 – Puller Magnet
2 – Extractor Bar
3 – Nano earpieces (2 magnetic units)
4 – Jack Connector, Keypad and Integrated Microphone
5 – Induction Collar
6 – Jack adapter
7 – External microphone
Check that it is a original PingaOculto product checking that the brand that appears on the cards included with the product is the same as the one in the image.
If you have doubts about whether the product is original, you can contact us by attaching an image and we will verify it. Contact us via: WhatsApp +34 644 098 320 o Email.
The penguins (in the image indicated by the number 3) are the two smallest pieces and should part with the nail. You can find them in the Kit in a bag. Also included are extractor bar (2 in the picture) and the puller magnet (1 in the image).
The Nano Induction Collar is divided into two separate parts that we will join in the next step. This inducer necklace requires two 9V batteries not included to work. Example 9V battery:
Connect the transmitter and receiver using the red connectors. Check that they are correctly oriented as in the image according to the shape of the connector.
If they are already connected, it is not necessary to perform this step.
Plug it in a 9V battery in each connector. Note that You must connect each port of the battery with the opposite of the connector to fit correctly. Check that they have been correctly fixed. The Estimated autonomy of the batteries is 3-4 hours depending on the volume and must be disconnected while the kit is not in use, since the induction collar uses energy even if it is not used.
Put the whole Kit on a table or flat surface and connect the mobile using the included headphone adapter. Plug the neckline jack into the green jack and the microphone into the red jack. Remove the cover of your mobile, since it can prevent the correct connection. If your mobile needs an adapter, verify that it works with other headphones to rule out a problem with the same one and check that it is original.
In some iPhone models, a compatibility failure has been detected in the use of the device with non-original adapters when making a phone call. You need to use an original adapter or use another mobile.
Place together the Extractor Magnet and the two earpieces and place them in contact with the induction collar like in the image. The extractor magnet, being also made of a piezoelectric material, reacts to inductive waves in the same way as the earpieces, vibrating and causing the sound and for this reason we will use it together with the earpieces to carry out the test.
Play a song on your mobile/MP3 and while playing turn up the volume to the maximum from your mobile. Bring your ear closer to the extractor magnet and to the earpieces that are in contact with the induction collar and check if it is heard and/or vibrates.
Si vibrate and/or can be heard the kit It's working correctly.
If they do not vibrate or hear anything, repeat the steps with another mobile and verify that the batteries are charged, that the connectors are correctly attached, that you have placed the extractor magnet and the two earpieces attached to the cable and that the volume is maximum while it is being used. play the song. If you need more help contact us: WhatsApp +34 644 098 320 o Email.
Enter first a penguin (only one of the two that appear in the image indicated by a 3) in the left ear (we hear better through the left ear than through the right) through the following procedure:
It may be necessary to spread this step several times
For check that the earpiece has been correctly inserted, put your hand to your ear (so that the earpiece does not fall to the ground) and turn your head to the opposite side. If the earpiece comes out of your ear easily when turning the head is that it has NOT been entered correctly. You must repeat the introduction steps.
also can check if it is correctly inserted by verifying that another person does not see the earpiece in the ear. If you can see it, DO NOT it is well introduced.
Tip: There are times when The earpiece just needs a little push to be correctly entered. If so, place the extractor magnet behind your ear, close to the neck. You will notice how the earpiece moves and you can finish placing it.
Tip 2: There are certain people who accumulate more amount of earwax, especially in the inner part of the ear, causing more difficult to introduce the earpiece. Remember clean the ear with Cleaning Sprays and sticks for the ears. Usually you will only need practice more to enter it correctly. If you can't enter it it is recommended that you have a ear cleaning to remove wax plugs.
If you can't enter it, contact us to help you: WhatsApp +34 644 098 320 o Email.
When the earpiece has been correctly inserted in the left ear, place the Kit as it appears in the image, remembering that the induction collar should always be on the neck under clothing. Batteries and mobile can be held in pockets or pants.
Play the song, recording or phone call by turning the volume up to the maximum on your mobile to check if the volume it provides is enough a penguin (sufficient in most cases) if we have inserted the earpiece correctly, if the volume is maximum, the batteries have enough charge and the induction collar is on the neck).
If you hear very low, Also insert the other earpiece into the right ear.
(A single earpiece in the left ear is recommended, since when trying to insert one in each ear, the first one will be misplaced when introducing the second one). (It is VERY likely that if we do not hear well with an earpiece in the left ear it is because we have not inserted the earpiece correctly, the volume is not the maximum in the mobile, the batteries are not sufficiently charged or the induction collar is not on the neck).
El Nano inductor collar should always be on the neck, since it is in charge of emitting short-range inductive waves to the earpiece, causing the sound. The inductor necklace being made of copper it is moldable and you can adjust it to the shape of your neck. For more security it is recommended to fix it with cloth or plastic tape to your skin so that it does not move during use. For repeated use you can even sew it to sweatshirts or jackets. Remember that the Inducer Collar is not washable and water will cause it to stop working.
You can use this Kit by phone call or with recordings. He integrated microphone is located behind the push button. El push button is not necessary if the functions are performed directly from the mobile. the push button it will not work if the red/green adapter is used y It may not be compatible with some mobiles, especially if you use an adapter to be able to connect it to the mobile:
remove the earpiece approaching the extractor bar (indicated in the image with a 2) with puller magnet (indicated with a 1) at its base to the ear as you can see in the first image.
Another VERY effective extraction method es hold with one finger the puller magnet inside the ear and shake your head while keeping it rotated as in the second image. It can be hard to remove the first few times, but after several attempts it will succeed.
As well the earpiece may have already been removed and fallen to the ground, check if it is still in your ear by connecting the Kit and checking if you hear when playing a song at maximum volume.
If you cannot extract it, contact us to help you: WhatsApp +34 644 098 320 o Email.
It is recommended to clean the earpiece with water or ethyl alcohol, the extractor magnet and the extractor bar before and after each use for better hygiene.
Finally, remember to disconnect the batteries when you finish using the device to prevent them from downloading. Never pull on the wires, pry between the battery and the connector.
Can check the VideoTutorial along with instructions to better understand how the earpiece works:
If you have questions, don't hesitate to contact us! 😉
the penguins can be complex products when putting them into operation. Check below the frequent problems of the nano microphone earpiece and its solution.
Nano earpieces work because of the material they are made of, a piezoelectric material, and not due to any internal electronics in the earpieces. For this reason it is impossible for nano earpieces not to work and The problem will be the inductor collar, the batteries or the mobile. Follow the steps and tests indicated in the next section.
Check that you have separated the earpieces (indicated in the image with the number 3), which are the two smallest pieces. You can find them in an accessory bag in the kit.
Verify that you have correctly connected the transmitter and receiver using the red connectors. Check that they are correctly oriented according to the shape of the connector. If they are already connected, there is no need to reconnect them.
Check that the 9V batteries are correctly seated in each connector and that the batteries are charged. Note that You must connect each port of the battery with the opposite of the connector to fit correctly. (If the batteries have been left connected for a long time they will be discharged, even if the unit has not been used they are spent).
If they do not vibrate or hear anything, repeat the steps with another mobile and verify that the batteries are charged, that the connectors are correctly attached, and that the volume is maximum while the song is playing. If you need more help contact us: WhatsApp +34 644 098 320 o Email.
If in the previous step when carrying out the test you have noticed how the extractor magnet together with the earpieces vibrate or sound, the kit is working correctly and the problem is:
If one earpiece works, the other works too. This is because the earpieces work because of the material they are made of, a piezoelectric material, and not due to any internal electronics in the earpieces. The material reacts to the inductive waves of the induction collar by vibrating and making sound.
Most likely, the earpiece has not been correctly inserted into the earOr this let's hear more for one than for another (normally we hear more through the left ear than through the right).
If the volume obtained by the earpiece in one ear is sufficient, it is recommended to use it with a single earpiece and save the other spare.
El push button is not necessary if the functions are performed directly from the mobile and may not be compatible with some mobiles, especially if adapters are used.
You can use this Kit by phone call or with recordings. He integrated microphone is located behind the push button.
Remember that eThe external microphone must be connected to the red connector with a microphone icon and the inductor collar in the green with the icon of a headset.
The external microphone can not work on mobiles with a non-original adapter, as for example usually happens on iPhone. It is recommended purchase an original adapter or use another mobile.
You may have to try several times until it is successfully removed.
remove the earpiece approaching the extractor bar (indicated in the image with a 2) with puller magnet (indicated with a 1) at its base to the ear as you can see in the picture.
⚠ If you can't extract it, contact us to help you: WhatsApp +34 644 098 320 o Email.
Earpieces work because of the material they are made of, a piezoelectric material, and not due to any internal electronics in the earpieces. For this reason it is impossible for nano earpieces not to work and the problem will be the inductor collar, the batteries or the mobile.
It is most likely that the batteries have remained connected and the batteries are exhausted. Remember to disconnect the batteries when you finish using the device to prevent them from downloading. You should never pull the wires to disconnect it, pry it up.
If the batteries have charge follow the steps indicated in the section 2 -I can't hear anything or very low.
If the Kit does not work, contact us to help you: WhatsApp +34 644 098 320 o Email.
Below is indicated important product information in relation to the security and compliance that guarantee proper and safe use of the product:
⚠ WARNING: Do not use or store the product near other electronic equipment because the magnetic field of adjacent electrical equipment will seriously damage or interfere with the product. Also do not use this product if you have impaired hearing which may be affected, if you use hearing aids, or if you are using a pacemaker or any electronic medical device.
Commercial Company: PingOc Now SL
® PingaOculto. All rights reserved.
Address: Calle Lucio del Valle 12, Local 1, 28003, Madrid, Spain.
Model Name: Nano + Microphone
Model Number: N-02
Product identifier: B08J8D77BP
Electrical Rating: 18V, 300-1000 mAh (Requires 2 9V Batteries not included)
Operating temperature: 0 to 35ºC
Product Use: Do not expose your device or adapter to liquids. If your device or adapter gets wet, carefully unplug all cables without getting your hands wet, and wait for the device and adapter to dry completely before plugging them back in. Do not try to dry your device or adapter with an external heat source, such as a microwave oven or blow dryer. If the device or adapter is damaged, stop using it immediately. Use only the supplied accessories to power your device. To avoid the risk of electric shock, do not touch the device or the cables connected to it during a thunderstorm. The cables and/or adapters are only designed for indoor use.
For EU customers: Hereby, PingaOculto, declares that the type of radio equipment is in compliance with Directive 2014/53/UE.
Radio Frequency Exposure Compliance: As a health protection measure, this device complies with the limits for exposure of the general public to electromagnetic fields in accordance with council recommendation 1999/519/EC. This device can be placed on the body avoiding prolonged use of it for more than 5 hours.
How to recycle your device properly: Disposal of certain electronic devices is regulated in some areas. Make sure you comply with local regulations and laws.
Additional Safety and Compliance Information: For additional information on safety, recycling and compliance or other important issues related to your device, do not hesitate to contact us through any of the available means of contact. Means of contact with: Email email@example.com, Call/WhatsApp +34 644 098 320.
Limited Warranty: All official PingaOculto brand items have a 2 year minimum warranty. This guarantee may be extended or reduced depending on the country where the sale takes place, as is the case by law in Spain where it is extended to 3 years as established by Decree-Law 7/2021 with respect to the Guarantee on the Sale of Goods. of consumption. We reserve the right to deny the guarantee of a product if improper or negligent use by the client is verified, similar to those reflected in: https://www.pingaoculto.es/garantias-y-devoluciones/ If you need to contact us due to a failure, you can do so by email: firstname.lastname@example.org or by Call/WhatsApp: +34 644 098 320.
Anywhere in the world
Up to 14 calendar days
Quick and Efficient Management
PayPal / MasterCard / Visa