4K Wifi Spy Camera Key Instructions
Table of Contents
- 1 4K Wifi Spy Camera Key Instructions
- 1.1 Key Spy Camera Wifi 4K
- 1.2 Technical characteristics
- 1.3 Contents
- 1.4 Instructions
- 1.5 Frequent Problems
- 1.6 Security and Compliance
Key Spy Camera Wifi 4K
Technical characteristics
- 4K UHD recording
- IMX 179 SONY 8.0MP sensor with WDR
- microSD storage
- Remote Transmission via WIfi
- Integrated Battery
Contents
Key Spy Camera Wifi 4K
Keychain with Opener
Screwdriver
USB Charging and Transfer Cable
Reset Clip
Manual
Instructions
Step 1 - Opening
The key hides a compartment for the MicroSD slot, Status LED, USB Connection and Reset.
At open the compartment it is due to pull hard holding the key with one hand and with the other pulling the cover or the ring.
Step 2 - Load
The battery is shipped with a low charge. It must of charge with a USB charger.
The key emits a Red light while charging that turns off when charging is 100%:
El charging time is about 2-3 hours when connected to a 1 amp charger at 5 Volts (
Maximum 5V 1.0A, using more amperage will reduce the useful life of the battery built into the key).
The camera automatically vibrates and turns on when charging. It is recommended to turn it off if not to be used while charging to reduce charging time. For it Press and hold the ON/OFF button on the key logo for 3 seconds until it vibrates, the green/yellow LED turns off and only the red LED remains on loading.
Step 3 - MicroSD
Introduce before ignition MicroSD into the slot until you hear a click. It is recommended to format the card to FAT 32 format and use a card with a Class 10 transfer speed. The minimum size allowed is 32 GB and the maximum 128 GB.
Step 4 - Power On/Off
Turn on the key holding down the logo button for 3 seconds of the key. This button has the key on/off function. The camera It will vibrate and the yellow LED will turn on without flashing. If Yellow LED flashes and continues to vibrate, the microSD has not been inserted before power on or the microSD format is incorrect. It is also possible that the microSD is smaller than 32GB, larger than 128GB, or defective.
At turn it off, repeat the procedure until the camera vibrates and the yellow LED turns off. If the camera is on for more than 5 minutes without Wi-Fi enabled, recording or video will be turned off automatically.
Step 5 - Video and Photography Recording
Press the trunk release button once to start with the recording. The key will vibrate and the red LED will start flashing. For stop recording, press the same button again. The red LED will stop flashing. If recording is not stopped, the camera will continue recording and will divide the recording into 5-minute videos for safety reasons.
Press the lock button once to perform a photography. The key will vibrate and the red LED will flash.
It is not possible to take photographs and video at the same time.
Step 6 – LED Off
Press and hold the lock button for 3 seconds to turn off the LEDs. It is very important to remember that This configuration will be stored and they will not turn on again until we hold the button again for 3 seconds.
will continue to vibrate to indicate when different actions are carried out, such as taking a photograph or video.
Step 7 - Wifi Remote Viewing
Step 7.1 - Application Download
Download the 4K Cam app on your mobile by pressing the Android or App Store (iPhone) icon depending on the model of your device.
It is important to grant all the required permissions in the app for your use.
Step 7.2 - Wifi connection
Press and hold the trunk release button for 3 seconds to turn on the camera's Wifi mode. When Wi-Fi is activated, a blue light will flash. Next, access the mobile's Wi-Fi settings and connect to the wifi network WIFI_XXXXXX with password 1234567890. If a notice appears when connecting indicating that this Wi-Fi network does not have internet and showing the option to maintain the connection or disconnect it, we must maintain the connection.
The blue light will stay on as long as there is a device connected via Wifi.
Step 7.3 - Wifi connection
Open the application and click on «Add New Camera«.
Select "Wi-Fi Connect«.
The application will recognize the wifi of the key to which we are connected and we will be able to visualize it. We can only view the camera in a range of approximately 10 meters; this model does not allow remote viewing.
La current battery will be indicated by a graphic in the upper left corner.
Step 7.4 - Change Resolution
While viewing the camera through the application you can change video or photo resolution. In addition, under the resolution change option the number of photographs or the recording time available in that resolution for the free size of the microSD will appear.
Depending on whether the mobile is Android or iPhone Some settings can be found by clicking on the gear wheel in the upper right corner.
At switch between photo/video mode Click on the icon in the lower right corner.
Step 7.5 - Gallery and Camera Settings
Click on the icon in the upper right corner to modify the settings such as white balance, date and time setting (automatically adjusted when pairing the key in the app), the recording frequency, the image resolution or modify the Wi-Fi network name and password.
Click on the icon in the lower left corner to view, download and share photographs and videos stored on the camera's microSD. They can also be viewed by inserting the microSD directly into the computer or using the included USB cable.
Step 8 - Reset
If the key is failing or we want to restore factory settings, insert the reset clip until it clicks and hold for at least 3 seconds. Then turn on the key.
Frequent Problems
1 - Does not turn on
The battery is shipped with a low charge. It must of charge with a USB charger.
The key emits a Red light while charging that turns off when charging is 100%:
El charging time is about 2-3 hours when connected to a 1 amp charger at 5 Volts (Maximum 5V 2.0A, using more amperage will reduce the useful life of the battery built into the key).
The camera automatically vibrates and turns on when charging. It is recommended to turn it off if not to be used while charging to reduce charging time. For it Press and hold the ON/OFF button on the key logo for 3 seconds until it vibrates, the green/yellow LED turns off and only the red LED remains on loading.
2 - Does not store
Enter the microSD into a computer and check that you can read it.
La microSD it is recommended that you have FAT32 format.
Remember to use a microSD between 32 and 128GB and that the transfer speed is minimum Class 10.
Security and Compliance
Below is indicated important product information in relation to the security and compliance that guarantee proper and safe use of the product:
® PingaOculto. All rights reserved.
Product specifications:
Model Name: 4K Spy Camera Key
Model Number:CE-16
Product identifier: 706212918430
Product battery: Integrated Lithium-Ion type with 900 mAh capacity
Operating temperature: 0 to 35ºC
Product Use: Do not expose your device or adapter to liquids. If your device or adapter gets wet, carefully unplug all cables without getting your hands wet, and wait for the device and adapter to dry completely before plugging them back in. Do not try to dry your device or adapter with an external heat source, such as a microwave oven or blow dryer. If the device or adapter is damaged, stop using it immediately. Use only the supplied accessories to power your device. To avoid the risk of electric shock, do not touch the device or the cables connected to it during a thunderstorm. The cables and/or adapters are only designed for indoor use.
Legal notice: PingOc Now SL is not responsible for the fraudulent or erroneous use of the product due to the lack of understanding or reading of the information in the instructions and precautions. This product is not a toy and must not be used contrary to current applicable laws. If you have any questions you can contact us before using the product.
For EU customers: Hereby, PingaOculto, declares that the type of radio equipment is in accordance with Directive 2014/53/EU.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC Compliance: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet the general RF exposure requirement. The device can be used in portable exposure conditions without restrictions.
Radio Frequency Exposure Compliance: As a health protection measure, this device complies with the limits for exposure of the general public to electromagnetic fields in accordance with council recommendation 1999/519/EC. This device can be placed on the body avoiding prolonged use of it for more than 5 hours.
How to recycle your device properly: Disposal of certain electronic devices is regulated in some areas. Make sure you comply with local regulations and laws.
Additional Safety and Compliance Information: For additional information on safety, recycling and compliance or other important issues related to your device, do not hesitate to contact us through any of the available means of contact. Means of contact with: Email contact@pingaoculto.com, Call/WhatsApp +34 644 098 320.
Limited Warranty: All official brand items PingaOculto have 2 year minimum warranty. This guarantee may be extended or reduced depending on the country where the sale takes place, as is the case by law in Spain where it is extended to 3 years as established by Decree-Law 7/2021 with respect to the Guarantee on the Sale of Goods. of consumption. We reserve the right to deny the guarantee of a product if improper or negligent use by the client is verified, similar to those reflected in: https://www.pingaoculto.es/garantias-y-devoluciones/ If you need to contact us due to a failure, you can do so by email: contact@pingaoculto.com or by Call/WhatsApp: +34 644 098 320.